- Home
- / Paints
- / Topside Paint
Interlux Interdeck Polyurethane Non-Skid Deck Coating is an excellent, easy to apply slip resistant polyurethane finish for decks. Interdeck contains a fine aggregate and will apply easily on all substrates. Interdeck provides a low sheen finish that helps protect against dazzle from sunlight reflected off decks. A tough polyurethane resin protects decks against everyday wear and tear. Interdeck is suitable for all substrates.
NOTE: Due to differences in monitors the colors shown on this page may not represent actual paint color.
| Drying Information | 41 degrees F | 59 Degrees F | 73 Degrees F | 95 Degrees F |
|---|---|---|---|---|
| Touch Dry (ISO) | 5 hours | 4 hours | 3 hours | 2 hours |
| Dry to Walk On | 4 days | 3 days | 2 days | 1 day |
| Overcoated By | Min-Max | Min-Max | Min-Max | Min-Max |
| Interdeck | 24 hrs - 4 days | 20 hrs - 3 days | 16 hrs - 2 days | 12 hrs - 1 day |
- APPLICATION AND USE
Preparation
BARE FIBERGLASS
In Good Condition: Begin by scrubbing well using soap and water and a stiff brush. Rinse with fresh water and allow to dry. Wipe a small area with a clean rag that has been wetted with Fiberglass Solvent Wash 202. While the surface is still wet, wipe with a clean, dry rag. Continue this process until the entire surface has been cleaned. Sand using 180-220 grade (grit) paper. Remove sanding residue.
MOLDED IN NON-SKID SURFACES
Scrub with Fiberglass Surface Prep YMA601 or Solvent Wash 202V using a 3M Doodlebug™ and a maroon Scotch-Brite® pad. Rinse with fresh water.
PREVIOUSLY PAINTED SURFACES
In Good Condition: The surface must be clean and dry. Sand with 220-320 grade (grit) paper. Remove sanding residue.
In Poor Condition: Remove all previous coatings and prime the substrate.
BARE WOOD
Sand surface, wipe clean. Apply Prekote Primer. Sand surface, wipe clean.
METAL
Use Interprotect 2000E to prime the surface of the prepared metal. See the Interprotect 2000E Technical Datasheet for bare metal preparation guidelines.
CLEAR EPOXY
Clean as for Bare Fiberglass above. Sand with 80 grade (grit) paper. Remove sanding residue. Apply one coat of Epoxy Primekote 404/414.
Method
Sand the primer with 180-220 grade wet or dry paper. Remove dust with a dust wipe. Apply 1-2 coats.
Hints
Mixing: Stir well before use.
Thinner: Brushing Liquid 333
Cleaner: Special Thinner 216
Ventilation and Humidity Control: Apply in dry, well ventilated conditions.
Other: For best results either stipple by brush or use a mohair roller.
Technical Information
- Finish: Low Sheen
- Specific Gravity:1.4
- Volume Solids:54%
- Typical Shelf Life:2 yrs
- Unit Size:1 US QUART
- Number of Coats:2 minimum
- Brush Coverage:(Theoretical) 386.7 (ft²/Gal)
- Spray Coverage:(Theoretical) 40 (ft²/Gal)
- Touch Dry Time: 41°F-5Hrs, 59°F-4Hrs, 73°F-3Hrs, 95°F-2Hr
- Walk-On Dry Time: 41°F-4 Days, 59°F-3 Days, 73°F-2 Days, 95°F-1 Day
TRANSPORTATION, STORAGE AND SAFETY INFORMATION
GENERAL INFORMATION: Exposure to air and extremes of temperature should be avoided. For the full shelf life of Interdeck to be realised ensure that between use the container is firmly closed and the temperature is between 5 deg C/40 deg F and 35 deg C/95 deg F. Keep out of direct sunlight.
TRANSPORTATION: Interdeck should be kept in securely closed containers during transport and storage.
DISPOSAL: Do not discard tins or pour paint into water courses, use the facilities provided. It is best to allow paints to harden before disposal.
Remainders of Interdeck cannot be disposed of through the municipal waste route or dumped without permit. Disposal of remainders must be arranged for in consultation with the authorities.
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov
Frequently Purchased Together
Recommended Products
Reviews for Interlux Interdeck Polyurethane Non-Skid Deck Coating
Verified Purchase
covered on coat and slip resistant
Was this review helpful to you?
Verified Purchase
Easy application, nice finish. Do not yet know how durable it will be. We'll see.
Was this review helpful to you?
Verified Purchase
Went on easy and looks good!
Was this review helpful to you?
Verified Purchase
There are very limited colors, but you can mix to get what you need. It is easy to apply and easy to patch in as needed. It s hard to move it fast enough in high heat and sunshine.
Was this review helpful to you?
After allowing two weeks to cure in normal summer temps - was still soft and was easily scuffed by chair legs. This paint may be okay for walking surfaces but I would not use this on any surface where paint will contact something hard like chair or table legs.
Was this review helpful to you?
Verified Purchase
I ordered the "Cream"... which rolls on like buttercup yellow! Not Jamestown's fault! I will be repainting with something else in the Fall! Easy application and good non-skid though!
Was this review helpful to you?
Verified Purchase
love this deck paint non-skid. even though it's a one part paint it last for quite a few years.
Was this review helpful to you?
Verified Purchase
Looks great and feels grippy, hope it lasts a few years. One coat seemed to cover nicely.
Was this review helpful to you?
Verified Purchase
Excellent nonskid deck finish. Easy to apply.
Was this review helpful to you?
Verified Purchase
This was really easy to use, and looks pretty good. Not a super aggressive non-skid paint, which is exactly what I wanted. Re-painted the cockpit sole on my C&C 24 with a foam brush and it came out great. If I were doing it again I'd probably use a foam roller but I'm very happy with the results.
Was this review helpful to you?
